Rear End Oil Seal

isaiahsdad · 08-02-2009, 12:49 PM

Got some oil wicking up the drive shaft so I am thinking the seal is bad in the final drive. Anyone replace it themselves? Any tips or tricks I need to know before I tear it down?? Not much of a drip and doesn't do it all the time. Just get a quarter size 'puddle' every once in a while and it doesn't matter how far I drive. Could go 50 miles and no puddle after, or could do 10 and have a drip. Any suggestions? And this started before I put my ct on. Should have tore it down then but didn't have the time or the seal. Thanks guys.

redjay · 08-02-2009, 01:08 PM

Hi, Ringadingh on here did his recently and posted photos. Maybe you can do a search and find them or contact him. I took my final drive off and took it to the dealers for them to do it.
It cost me $180 Canadian if I remember correctly. Talk to the dealer to order the parts ahead of time (a seal, O rings, and a large nut that is tabbed over) as they will likely not have them in stock. That way your downtime is reduced.

**ringadingh** · 08-02-2009, 01:58 PM

Its not that difficult to do yourself, if your handy, Its a $8.00 seal that you need to replace, there is a tool the recomend that you use to remove the lock collar but I used a drift punch and tapped it out with that, the lock collar is a lh thread, and is also held in place with a small setscrew that needs to be loosened first. The important thing is to look closely where the seal sits in the collar, and replace it in the same place. There is a lot of room to put the seal in either to deep or not deep enough. Also polish the pinion shaft a bit with some emery cloth before reassembly.
Try to find the thread here as it has some pics of what youll be getting into. You only need to remove the pinion shaft, the ring gear is not to be removed unless that seal is leaking. If the ring gear seal is bad it will throw oil all over the tire sidewall.

macmac · 08-02-2009, 02:20 PM

Ring's link ( I saved it)

http://www.vulcanbagger.com/phpBB3/viewtopic.php?t=9764

Be sure to ck and top off that oil untill the work is done. The so called 6.2 ounces isn't very much oil in the first place.

08-02-2009, 12:49 PM	#1
isaiahsdad Member Join Date: Jun 2009 Location: Midwest City, Oklahoma, USA Posts: 246	Rear End Oil Seal Got some oil wicking up the drive shaft so I am thinking the seal is bad in the final drive. Anyone replace it themselves? Any tips or tricks I need to know before I tear it down?? Not much of a drip and doesn't do it all the time. Just get a quarter size 'puddle' every once in a while and it doesn't matter how far I drive. Could go 50 miles and no puddle after, or could do 10 and have a drip. Any suggestions? And this started before I put my ct on. Should have tore it down then but didn't have the time or the seal. Thanks guys. Login or Register to Remove Ads
	0

08-02-2009, 01:08 PM	#2
redjay Top Contributor Join Date: Feb 2008 Location: Ontario Posts: 7,017	Rear End Oil Seal Hi, Ringadingh on here did his recently and posted photos. Maybe you can do a search and find them or contact him. I took my final drive off and took it to the dealers for them to do it. It cost me $180 Canadian if I remember correctly. Talk to the dealer to order the parts ahead of time (a seal, O rings, and a large nut that is tabbed over) as they will likely not have them in stock. That way your downtime is reduced.
	0

08-02-2009, 01:58 PM	#3
ringadingh Join Date: Aug 2007 Location: Newmarket Ontario Canada Posts: 35,387	Rear End Oil Seal Its not that difficult to do yourself, if your handy, Its a $8.00 seal that you need to replace, there is a tool the recomend that you use to remove the lock collar but I used a drift punch and tapped it out with that, the lock collar is a lh thread, and is also held in place with a small setscrew that needs to be loosened first. The important thing is to look closely where the seal sits in the collar, and replace it in the same place. There is a lot of room to put the seal in either to deep or not deep enough. Also polish the pinion shaft a bit with some emery cloth before reassembly. Try to find the thread here as it has some pics of what youll be getting into. You only need to remove the pinion shaft, the ring gear is not to be removed unless that seal is leaking. If the ring gear seal is bad it will throw oil all over the tire sidewall. __________________ 2002 Nomad aka Bountyhunter VBA #27 VROC #18951
	0

08-02-2009, 02:20 PM	#4
macmac Sr. Contributor Join Date: Apr 2008 Location: Tamworth New Hampster 06 1600 Posts: 12,484	Rear End Oil Seal Ring's link ( I saved it) http://www.vulcanbagger.com/phpBB3/viewtopic.php?t=9764 Be sure to ck and top off that oil untill the work is done. The so called 6.2 ounces isn't very much oil in the first place. __________________ 06 1600 Nomad Just call me Mac molon labe come and get it
	0

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Clutch Rod Oil Seal Lost	jonsamson	1500 & 1600 Nomad	21	01-13-2011 11:38 AM
Rear seal question	jmb	1500 & 1600 Nomad	6	09-29-2009 12:25 AM
Final drive oil seal part#?	redeye	1500 & 1600 Nomad	8	12-30-2008 08:39 PM
Rear seal leaking again	finky	1500 & 1600 Nomad	3	12-09-2008 12:07 PM
rear pinion seal	rickmeister56	1500 & 1600 Nomad	2	07-07-2008 07:09 PM