|
03-31-2012, 09:55 PM | #1 |
Jr. Member
Join Date: Mar 2010
Location: Prince Rupert
Posts: 34
|
Adjusting tension on 09/Nomad drive belt
Searched the topic but, could not find specific information.
Manual says 3-4.5mm deflection with 10lbs of force and rear wheel off of the ground. Seems tight as the swing arm will move and put more tension on the belt when weight of bike moves the swing arm. I'm no disbuting the manual, however just seems tight. What do you folks normally do when adjusting the belt tension. Login or Register to Remove Ads |
|
03-31-2012, 10:28 PM | #2 | |
Sr. Member
Join Date: Mar 2012
Location: Orleans, ON, Canada
Posts: 1,162
|
Quote:
__________________
Smokey Capt(retd) Canadian Forces National President CVFR (Canadian Veteran Freedom Riders) 2010 VN1700 Voyager, ABS www.cvfr.ca VBA #02220 |
|
|
04-02-2012, 02:43 AM | #3 |
Member
Join Date: Sep 2010
Location: Southern Oregon
Posts: 224
|
I set mine at a loose 5mm also. The belt gets tighter as it gets warmer, so I set the belt cold on a normal temp day with the back tire off the ground. The carbon fiber belts are made to run tight, but I don't feel good about getting it too tight and put extra pressure on the drive sprocket bearings.
I have run mine as loose as 10mm deflection at 10 lbs and it ran good there also. I tried the looser 10mm when I got a lot of belt damage to see if it ran quieter, but went back to the 5mm deflection. I think Harley runs their belts at 5/16" to 3/8" (8mm to 9.5mm), maybe someone can tell you more about Harleys. I'm no expert, just my opinion. James
__________________
Kawasaki 2010 Nomad 1700 Southern Oregon Vance & Hines slash cut slip-ons Cobra Powerpro CVT Thunder Air Kit, stock cover Kuryakyn Power Point 12v adaptor Cobra Luggage Rack Grasshopper back rest Tomtom GPS |
|
04-02-2012, 07:34 AM | #4 |
Member
Join Date: Feb 2012
Posts: 63
|
What are you guys using to apply the 10 pounds of force?
__________________
2010 Voyager: Vance & Hines Pro Pipe with Supertrapp meg can, Thunder Air kit, Corbin heated seat, Fuel cap mod (close w/o key), I-Pod, Thermometer, mounted dual heat-troller, rear speakers, rear rack, bag liners, Dobeck's Gen 3, grips, backrest, removable coffee holder, 1500 kick-stand, marbled, air horn, adjustable windshield (8"-12.5"), Race Tech Gold Valve Cartridge Fork Emulator & springs, Küryakyn floorboard mount Hwy pegs, etc... Other rides: 2003 ZRX1200r (X2) 2006 ZX14 |
|
04-02-2012, 08:18 AM | #5 |
Sr. Member
Join Date: Mar 2012
Location: Orleans, ON, Canada
Posts: 1,162
|
I have an actual tool used for that, called a belt drive tensioner.
http://www.amazon.com/Motion-Pro-Bel.../dp/B002OPK97I http://www.motorcycle-superstore.com...ion-Gauge.aspx is one place but I have seen them cheaper than that.
__________________
Smokey Capt(retd) Canadian Forces National President CVFR (Canadian Veteran Freedom Riders) 2010 VN1700 Voyager, ABS www.cvfr.ca VBA #02220 Login or Register to Remove Ads |
|
04-02-2012, 12:20 PM | #6 |
Member
Join Date: Sep 2010
Location: Southern Oregon
Posts: 224
|
I use the motion pro belt tension gauge. To get it to read correctly make sure you push straight up on the belt, not at an angle.
James
__________________
Kawasaki 2010 Nomad 1700 Southern Oregon Vance & Hines slash cut slip-ons Cobra Powerpro CVT Thunder Air Kit, stock cover Kuryakyn Power Point 12v adaptor Cobra Luggage Rack Grasshopper back rest Tomtom GPS |
|
04-02-2012, 03:50 PM | #7 |
Jr. Member
Join Date: Mar 2010
Location: Prince Rupert
Posts: 34
|
Thank you for the info, just seems tight. My worry is the same, putting pressure on the counter shaft output shaft seal. I'm more familiar with chain and the slack with them.
|
|
04-02-2012, 06:26 PM | #8 |
Member
Join Date: Feb 2012
Posts: 63
|
Thanks guys, I'll track one down for my tool box :-)
__________________
2010 Voyager: Vance & Hines Pro Pipe with Supertrapp meg can, Thunder Air kit, Corbin heated seat, Fuel cap mod (close w/o key), I-Pod, Thermometer, mounted dual heat-troller, rear speakers, rear rack, bag liners, Dobeck's Gen 3, grips, backrest, removable coffee holder, 1500 kick-stand, marbled, air horn, adjustable windshield (8"-12.5"), Race Tech Gold Valve Cartridge Fork Emulator & springs, Küryakyn floorboard mount Hwy pegs, etc... Other rides: 2003 ZRX1200r (X2) 2006 ZX14 |
|
04-04-2012, 03:32 AM | #9 |
Top Contributor
Join Date: Aug 2011
Location: North Wilkesboro, NC
Posts: 6,289
|
Until you get one of those devices, a US gallon of water weighs roughly 8.35 pounds. Get 2 gallon jugs and fill each of them 60% full. Tie them together then hang them from the belt. If you buy milk by the gallon, you're not out anything.
__________________
Christopher "Monkeyman" Gray ---------------------------- Widows Sons "Overseers" Patriot Guard Rider USArmy 1987-1990 2021 Can Am Spyder RT 2018 Can Am Spyder RT Limited - SOLD 2014 Nomad - SOLD 2012 Victory Vision - SOLD 2007 Black Nomad - SOLD VMC #9367 VBA #1860 |
|
04-04-2012, 07:42 AM | #10 | |
Member
Join Date: Feb 2012
Posts: 63
|
Quote:
I was going to try to use a 10lb weight (gym type dumbbell) but I've got a thing for tools so I couldn't resist; I ordered a tension gauge last night :-)
__________________
2010 Voyager: Vance & Hines Pro Pipe with Supertrapp meg can, Thunder Air kit, Corbin heated seat, Fuel cap mod (close w/o key), I-Pod, Thermometer, mounted dual heat-troller, rear speakers, rear rack, bag liners, Dobeck's Gen 3, grips, backrest, removable coffee holder, 1500 kick-stand, marbled, air horn, adjustable windshield (8"-12.5"), Race Tech Gold Valve Cartridge Fork Emulator & springs, Küryakyn floorboard mount Hwy pegs, etc... Other rides: 2003 ZRX1200r (X2) 2006 ZX14 |
|
|
04-04-2012, 09:22 PM | #11 |
Member
Join Date: Nov 2011
Location: Oklahoma
Posts: 95
|
I took mine to the dealer twice right after I bought it because it was squealing. They checked it with a gauge and said in was in spec according to Kawasaki. I know what a belt sounds like when its to tight and this was to tight. So I backed it off and used my hand to determine the correct tension. Belt is much quieter and still tight enough to keep belt from any damage. As a matter of fact a belt stretched to tight will wear quickly. I know some will say you shouldn't set a belt by feel, but it has proven good enough for a $250,000 combine so.......
|
|