ignition coil

albrightb · 01-05-2009, 10:25 AM

I suddenly loss spark to the rear cyclinder of my 04 nomad. One day fine next day (after giving it a gentle wash) no spark. Service manager at local shop thought moister but later decided in was the rear coil. Has anyone had a similar problem? Bike has only 6T miles. Also getting part from Kawa is taking forever. Please offer any and all suggestions and/or explanations. Thanks Buzz

cactusjack · 01-05-2009, 12:29 PM

I always "blow dry" my Nomad with a leaf blower after washing to get water out of the nooks and crannies. I guess you need to make sure you are getting power to the rear coil. Are there not 2 spark plugs per cyclinder on an '04? If both plugs are not getting juice, check to see if there's even juice getting to the coil.

redeye · 01-05-2009, 02:56 PM

I found this on the Beartooth Kawasaki Forum. I thought it might help you with diagnosing your problem.

1. Make sure the ignition switch is OFF.
2. Pull out the ECU and connect terminal #37 to the negative terminal on the battery using a piece of wire.
3. Turn the ignition switch to the ON position.
4. The FI indicator light will then display the fault code by flashing a series of blinks. Each fault will be displayed three times before the next fault. The coding goes like *blink*pause 1 second, then *blink*blink*. Such a series of blinks indicate code is #12.
5. The codes that may be displayed are: 11-throttle sensor malfunction; 12-vacuum sensor malfunction; 13-inlet air temp sensor malfunction; 14-water temp sensor malfunction; 15-atmospheric pressure sensor malfunction; 21- pickup coil #1 malfunction; 22-pickup coil #2 malfunction; 31-vehicle down sensor malfunction; 41-injector #1 malfunction; 42-injector #2 malfunction; 45-fuel pump malfunction; 51-ignition coil #1 primary winding malfunction; 52- ignition coil #2 primary winding malfunction

Most of these faults relate to a short or open in the wiring or in the sensor.

Thread Tools	Search this Thread
Show Printable Version Email this Page	Search this Thread: Advanced Search
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Coil Question	macmac	1500 & 1600 Nomad	9	05-22-2010 12:34 PM
Ignition Relocation	soverton	Vulcan Nomad/Vaquero/Voyager	12	11-03-2009 12:40 PM
New ignition	475772	1500 & 1600 Nomad	9	07-14-2009 06:20 PM
ignition relocation	speedbyu	Vulcan Nomad/Vaquero/Voyager	24	05-25-2008 05:54 AM
Nomad Coil	mercianbike	1500 & 1600 Nomad	3	11-30-2007 12:01 PM

01-05-2009, 10:25 AM	#1
albrightb Jr. Member Join Date: Sep 2008 Posts: 8	ignition coil I suddenly loss spark to the rear cyclinder of my 04 nomad. One day fine next day (after giving it a gentle wash) no spark. Service manager at local shop thought moister but later decided in was the rear coil. Has anyone had a similar problem? Bike has only 6T miles. Also getting part from Kawa is taking forever. Please offer any and all suggestions and/or explanations. Thanks Buzz Login or Register to Remove Ads
	0

01-05-2009, 12:29 PM	#2
cactusjack Mega-Contributor Join Date: Sep 2007 Location: Where it doesn't snow...ever! Posts: 21,926	ignition coil I always "blow dry" my Nomad with a leaf blower after washing to get water out of the nooks and crannies. I guess you need to make sure you are getting power to the rear coil. Are there not 2 spark plugs per cyclinder on an '04? If both plugs are not getting juice, check to see if there's even juice getting to the coil. __________________ Scott "Cactusjack" Hanks VBA #00105 H.O.G. #4250060 2011 H-D Ultra Limited 103ci :: 2011 HD Electra Glide Ultra Limited w/Stage 1 :: Rallies: Mesquite '08\|Custer '09\|Cortez '10\|Crescent City '11\|Kanab '12\|Antlers '12\|Estes Park '13\|Antlers '13\|Orofino '14\|The Dalles '17
	0

01-05-2009, 02:56 PM	#3
redeye Advanced Member Join Date: Dec 2007 Location: Rocklin California Posts: 777	ignition coil I found this on the Beartooth Kawasaki Forum. I thought it might help you with diagnosing your problem. 1. Make sure the ignition switch is OFF. 2. Pull out the ECU and connect terminal #37 to the negative terminal on the battery using a piece of wire. 3. Turn the ignition switch to the ON position. 4. The FI indicator light will then display the fault code by flashing a series of blinks. Each fault will be displayed three times before the next fault. The coding goes like blinkpause 1 second, then blinkblink*. Such a series of blinks indicate code is #12. 5. The codes that may be displayed are: 11-throttle sensor malfunction; 12-vacuum sensor malfunction; 13-inlet air temp sensor malfunction; 14-water temp sensor malfunction; 15-atmospheric pressure sensor malfunction; 21- pickup coil #1 malfunction; 22-pickup coil #2 malfunction; 31-vehicle down sensor malfunction; 41-injector #1 malfunction; 42-injector #2 malfunction; 45-fuel pump malfunction; 51-ignition coil #1 primary winding malfunction; 52- ignition coil #2 primary winding malfunction Most of these faults relate to a short or open in the wiring or in the sensor.
	0