ignition fuse blows

nomad · 04-07-2011, 05:28 PM

My ignition fuse blows when i turn the key on. Before i tear into this thing, does anyone here have experience with this particular problem? If not, i guess i have to strip it down and start disconnecting things one at a time til i find out with component is causing the problem. when i took the right sidecover off, the coolant tank was empty also. i found no evidence of coolant leaking or causing any shorts...etc. this could take a while...... ::)

AlabamaNomadRider · 04-07-2011, 06:37 PM

Do you have any accessories installed that use the same circuit? Something is causing an overload. Unless there is a short and that is causing the fuse to blow.

chuckster131 · 04-07-2011, 07:03 PM

Check the main harness if it is a 1500 it goes right up and over the rear rocker cover. Mine had rubbed right into the wires and was blowing the 30amp main fuse.

nomad · 04-07-2011, 07:53 PM

its the 10 amp ignition fuse that blows. it powers the idiot lights on the inst. panel, it powers the dfi relay (fuel injection). as well as both start circuit relays and the headlight relay. my parking lights work, the back lighting on the inst. panel works...and thats about it. i have tried 3 fuses after reseating connectors and re-positioning wiring...and it still blows. its a wiring issue or a component has failed. it ran great when i parked it last night. so far i have got the right side cover, the inst. panel and the gas tank off. no issues seen so far. i may add the gas tank was a pain in the butt....lol!

cactusjack · 04-07-2011, 08:05 PM

Could be a shorted ignition switch, too.

**ringadingh** · 04-07-2011, 08:07 PM

Check closely where Joe mentioned, thats a common spot for the harness to screw up. Also check the wires right under the seat around the battery. Sometimes they will short out there after being compressed over the years by the seat.
Also check the headlight bulb, it may be blown and the broken filament is causing a short, its a longshot but Ive seen it happen more than once. Look in the headlight bucket to see if any wires have rubbed through in there as well.

nomad · 04-07-2011, 10:02 PM

unplugged the headlight and right handlebar electrical controls...and i ohmed the wire from the ignition fuse to ground. its open. (no shorts). so now i'm looking at a component failure. thats a good suggestion with the headlight, i'll check it out. not sure where the DFI relay is...i still have that to check. on a side note, found some loose clamps under the tank that would explain my coolant loss, so i guess its not a total waste of time. what are the odds that the junction box or ECU is bad? this wire only runs to a few components.

edited to add...never thought about the ignition switch...good suggestion as well. :)

AlabamaNomadRider · 04-07-2011, 10:50 PM

I doubt it being a bad ECU. The bike probably wouldn't start or if it did it would run like crap.

**cnc** · 04-08-2011, 07:28 AM

Quote:

Originally Posted by Nomad

unplugged the headlight and right handlebar electrical controls...and i ohmed the wire from the ignition fuse to ground. its open. (no shorts). so now i'm looking at a component failure. thats a good suggestion with the headlight, i'll check it out. not sure where the DFI relay is...i still have that to check. on a side note, found some loose clamps under the tank that would explain my coolant loss, so i guess its not a total waste of time. what are the odds that the junction box or ECU is bad? this wire only runs to a few components.

edited to add...never thought about the ignition switch...good suggestion as well. :)

I presume from your response that you have the wiring diagram and a multi meter and you seem to have a good handle on the search process.
I was just thinking if it was me, after checking the ignition switch it's self for a short to ground, remove the individual wires from the ignition plug ( I am presuming it is a plug, I'm just looking at the diagram ) and replug them individually till you blow the fuse.
You then have a direction to go in following the wires and components that that wire feeds.

**ringadingh** · 04-08-2011, 08:48 AM

All of the relays are located on the RH side by the junction box. If its not something you have found yet, youll have to eliminate each circuit one by one, or disconnect all of them if you can and see if a fuse blows. Then you can reconnect the wires one by one until it blows to try to pinpoint the problem.

nomad · 04-09-2011, 11:43 AM

found it...the PO had powered the aux driving lights with the hot wire to the coils..(yep, thats right...). why he did this i do not know. whenever i flipped the kill switch to run the fuse popped. his wiring job was lacking to say the least. i hooked them up correctly and to a less critical power source. so far, everything is A-OK. i want to thank everyone for the advice and help.

cactusjack · 04-09-2011, 12:45 PM

Quote:

Originally Posted by Nomad

found it...the PO had powered the aux driving lights with the hot wire to the coils..(yep, thats right...). why he did this i do not know. whenever i flipped the kill switch to run the fuse popped. his wiring job was lacking to say the least. i hooked them up correctly and to a less critical power source. so far, everything is A-OK. i want to thank everyone for the advice and help.

Please tell us you used a relay?

nomad · 04-09-2011, 11:19 PM

Quote:

Originally Posted by cactusjack

Quote:

Originally Posted by Nomad

found it...the PO had powered the aux driving lights with the hot wire to the coils..(yep, thats right...). why he did this i do not know. whenever i flipped the kill switch to run the fuse popped. his wiring job was lacking to say the least. i hooked them up correctly and to a less critical power source. so far, everything is A-OK. i want to thank everyone for the advice and help.

Please tell us you used a relay?

no...and i should have. i was so impatient to ride that i used the forward accessory wiring to power the lights...the downside to that is now they will come on even when the key is out of the ignition switch. i was in such a hurry to take advantage of this weekends good weather that i didn't consult the wiring charts first. i just assumed that they were powered on with the key. oh well, haste makes waste. back to the drawing board. i guess the PO and myself are in the same boat...lol. :)

**ringadingh** · 04-10-2011, 12:32 AM

I had a similar situation with the driving lamps on my bike yesterday. I am installing a small six fuse panel and a relay so I have more switched circuits available.
Don't leave it wired like that on your bike, if you ever forget to turn off the switch youll end up with a dead battery in a hurry.

nomad · 04-10-2011, 07:35 AM

Quote:

Originally Posted by Ringadingh

I had a similar situation with the driving lamps on my bike yesterday. I am installing a small six fuse panel and a relay so I have more switched circuits available.
Don't leave it wired like that on your bike, if you ever forget to turn off the switch youll end up with a dead battery in a hurry.

sound advice. that acc. fuse panel sounds like a good idea. where did you find the fuse panel? any auto parts place carry them?

04-07-2011, 05:28 PM	#1
nomad Member Join Date: Jul 2008 Location: central mississippi Posts: 443	ignition fuse blows My ignition fuse blows when i turn the key on. Before i tear into this thing, does anyone here have experience with this particular problem? If not, i guess i have to strip it down and start disconnecting things one at a time til i find out with component is causing the problem. when i took the right sidecover off, the coolant tank was empty also. i found no evidence of coolant leaking or causing any shorts...etc. this could take a while...... ::) Login or Register to Remove Ads
	0

04-07-2011, 06:37 PM	#2
AlabamaNomadRider Sr. Contributor Join Date: Jul 2009 Location: Boaz, Alabama Posts: 13,742	ignition fuse blows Do you have any accessories installed that use the same circuit? Something is causing an overload. Unless there is a short and that is causing the fuse to blow. __________________ Gene Cross, Jr. Boaz, Alabama KawaNOW/VBA #1181
	0

04-07-2011, 07:03 PM	#3
chuckster131 Sr. Member Join Date: Sep 2007 Location: Jackson, Michigan Posts: 1,367	ignition fuse blows Check the main harness if it is a 1500 it goes right up and over the rear rocker cover. Mine had rubbed right into the wires and was blowing the 30amp main fuse. __________________ Joe (Chuckster) Norris Jackson, Michigan 2007 Goldwing 2010 Voyager (Blue/Silver)sold 2001 Nomad (gone, but not forgotten) www.chucksterscustoms.com
	0

04-07-2011, 07:53 PM	#4
nomad Member Join Date: Jul 2008 Location: central mississippi Posts: 443	ignition fuse blows its the 10 amp ignition fuse that blows. it powers the idiot lights on the inst. panel, it powers the dfi relay (fuel injection). as well as both start circuit relays and the headlight relay. my parking lights work, the back lighting on the inst. panel works...and thats about it. i have tried 3 fuses after reseating connectors and re-positioning wiring...and it still blows. its a wiring issue or a component has failed. it ran great when i parked it last night. so far i have got the right side cover, the inst. panel and the gas tank off. no issues seen so far. i may add the gas tank was a pain in the butt....lol!
	0

04-07-2011, 08:05 PM	#5
cactusjack Mega-Contributor Join Date: Sep 2007 Location: Where it doesn't snow...ever! Posts: 21,926	ignition fuse blows Could be a shorted ignition switch, too. __________________ Scott "Cactusjack" Hanks VBA #00105 H.O.G. #4250060 2011 H-D Ultra Limited 103ci :: 2011 HD Electra Glide Ultra Limited w/Stage 1 :: Rallies: Mesquite '08\|Custer '09\|Cortez '10\|Crescent City '11\|Kanab '12\|Antlers '12\|Estes Park '13\|Antlers '13\|Orofino '14\|The Dalles '17 Login or Register to Remove Ads
	0

04-07-2011, 08:07 PM	#6
ringadingh Join Date: Aug 2007 Location: Newmarket Ontario Canada Posts: 35,387	ignition fuse blows Check closely where Joe mentioned, thats a common spot for the harness to screw up. Also check the wires right under the seat around the battery. Sometimes they will short out there after being compressed over the years by the seat. Also check the headlight bulb, it may be blown and the broken filament is causing a short, its a longshot but Ive seen it happen more than once. Look in the headlight bucket to see if any wires have rubbed through in there as well. __________________ 2002 Nomad aka Bountyhunter VBA #27 VROC #18951
	0

04-07-2011, 10:02 PM	#7
nomad Member Join Date: Jul 2008 Location: central mississippi Posts: 443	ignition fuse blows unplugged the headlight and right handlebar electrical controls...and i ohmed the wire from the ignition fuse to ground. its open. (no shorts). so now i'm looking at a component failure. thats a good suggestion with the headlight, i'll check it out. not sure where the DFI relay is...i still have that to check. on a side note, found some loose clamps under the tank that would explain my coolant loss, so i guess its not a total waste of time. what are the odds that the junction box or ECU is bad? this wire only runs to a few components. edited to add...never thought about the ignition switch...good suggestion as well. :)
	0

04-07-2011, 10:50 PM	#8
AlabamaNomadRider Sr. Contributor Join Date: Jul 2009 Location: Boaz, Alabama Posts: 13,742	ignition fuse blows I doubt it being a bad ECU. The bike probably wouldn't start or if it did it would run like crap. __________________ Gene Cross, Jr. Boaz, Alabama KawaNOW/VBA #1181
	0

04-08-2011, 08:48 AM	#10
ringadingh Join Date: Aug 2007 Location: Newmarket Ontario Canada Posts: 35,387	ignition fuse blows All of the relays are located on the RH side by the junction box. If its not something you have found yet, youll have to eliminate each circuit one by one, or disconnect all of them if you can and see if a fuse blows. Then you can reconnect the wires one by one until it blows to try to pinpoint the problem. __________________ 2002 Nomad aka Bountyhunter VBA #27 VROC #18951
	0

04-09-2011, 11:43 AM	#11
nomad Member Join Date: Jul 2008 Location: central mississippi Posts: 443	ignition fuse blows found it...the PO had powered the aux driving lights with the hot wire to the coils..(yep, thats right...). why he did this i do not know. whenever i flipped the kill switch to run the fuse popped. his wiring job was lacking to say the least. i hooked them up correctly and to a less critical power source. so far, everything is A-OK. i want to thank everyone for the advice and help.
	0

04-10-2011, 12:32 AM	#14
ringadingh Join Date: Aug 2007 Location: Newmarket Ontario Canada Posts: 35,387	ignition fuse blows I had a similar situation with the driving lamps on my bike yesterday. I am installing a small six fuse panel and a relay so I have more switched circuits available. Don't leave it wired like that on your bike, if you ever forget to turn off the switch youll end up with a dead battery in a hurry. __________________ 2002 Nomad aka Bountyhunter VBA #27 VROC #18951
	0

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
New ignition	475772	1500 & 1600 Nomad	9	07-14-2009 06:20 PM
blows a little smoke	borto1990	1500 & 1600 Nomad	19	04-14-2009 05:27 PM
White knuckle ride in-- The wind blows (and sucks)	bobhamlin	Vulcan Nomad/Vaquero/Voyager	3	02-12-2009 08:42 PM
ignition relocation	speedbyu	Vulcan Nomad/Vaquero/Voyager	24	05-25-2008 05:54 AM
Stebel horn blows fuse.	bobzinger	1500 & 1600 Nomad	22	04-21-2008 05:50 PM