Your Nomad Dyno results?

[socwkbiker]

Does anyone have a link to easy to read and understand installation instructions for a PC III?

Yup I sure do.
Just know there is somethings in there you dont have to do. It took my like an hour + to install mine and thats becasue i never did one on a 1600 nomad and plus it was the first time pulling my tank. Now it wouldnt take more than 30 mintues tops. This PC for our bikes is one of the easit to install from Dynojet. Let me know what else I can do to help.
Link below it's a pdf file!
http://www.powercommander.com/downlo...eng220-411.pdf

It's gonna have to be pretty easy.................... for me to understand!!! lol

<marquee> </marquee>

It's gonna have to be pretty easy.................... for me to understand!!! lol

<marquee> </marquee>

ROFLOL trust me if i can do so can you LOL

I really don't think I'll be able to figure out how to use it on my '99 carbed model...... :'(

I really don't think I'll be able to figure out how to use it on my '99 carbed model...... :'(

Yeah would be tuff to use on a carbed bike ROFLOLOLOLOLOL :) :)

<marquee> ??? :-[ :-/ ::) :( ;) </marquee>

[blowndodge]

Shucks you should have kept quiet! All Thumbs (Nico) would have tried to do it anyway!!! LOLOLO
l

I know I can make it work..... gimme a hammer.... :-/

[dogdoc]

Chuck: If you had V&H pipes, hypercharger air cleaner and PClll, would it be enough to just download the set map for the nomad? or I know if you want top power you have to do the dyno right? here they charge like $300+ to dyno it and it takes most of the day the guy said. Somebody else on here said and a new rear tire also? Any insight would be helpfull. Did it correct all the popping on decleration?

Doc

Chuck: If you had V&H pipes, hypercharger air cleaner and PClll, would it be enough to just download the set map for the nomad? or I know if you want top power you have to do the dyno right? here they charge like $300+ to dyno it and it takes most of the day the guy said. Somebody else on here said and a new rear tire also? Any insight would be helpfull. Did it correct all the popping on declaration?

Doc

Hey Doc, To answer your questions yes it would be enough to Download a map from dynojet for the nomad with all the extra mods you mentioned. BUT there maps seem to run very rich. If you go and do all that to your bike I have my map from when i got my dyno'd and I think I have another nomad dyno map from a friend back in seattle who has an 06 like me. I can e-mail them to ya or put them on disc and mail them to ya. The reason they say it takes all day is because it depends on how close your map is to being good before they dyno your bike. I had a pretty good map on mine done by gervasi' in Everett, Wa just using a gas analyzer and it took them maybe an hour to an hour and half at most. No you wont need a new tire after a basic dyno. Where do these urban legends come from ROFLOLOLOL.

Also once i had my bike mapped right I have NOT HAD ONE POP on my bike since getting it done. Not one!!!!! Does not matter what gear I'm in the bike never pops on deceleration. Hope this helps...

[dogdoc]

Thanks for the info VC.

Doc

Not even a problem Doc...

[socwkbiker]

Thanks for all the info VC. I'll be picking up my PC III today and hopefully installing it this weekend.

Soc very cool. Let me know if you have any issues with it. My install looks factory becasue I took the time to zip tie the wires to the back bone wireharness on the bike so its a good fit. Let me know what you think of it once you get it installed. Again if you need any help let me know and i can shoot you my cell #