|
|
09-22-2014, 09:05 PM
|
#1 |
|
Sr. Member
Join Date: Mar 2010
Location: Tallahassee FL
Posts: 1,032
|
Clutch spring/brake switch
Replacing my clutch spring, gadgets instructions say to remove the brake switch from the housing by turning the housing and not the switch due possibility of breaking a wire... Question is how is that done? Pics/help much appreciated as I am going on a trip on Thrs.
Login or Register to Remove Ads |
|
|
09-22-2014, 09:52 PM
|
#2 |
 
Join Date: Oct 2010
Location: Michigan
Posts: 1,286
|
My bike had a plastic sleeve that held the switch and it has ears that are compressed to get it to release from the bracket it is in. If you cant get it to release it should unthread from the switch. Hold the switch still and unscrew the sleeve from the switch.
Hope this helps DC
__________________
Me and my 99 G1 Nomad on US 2 by the Lake Michigan Shoreline. Judge's Oil Gear failed and engine overhauled @ 35563 miles  VBA/KawaNOW #01625 Christian Motorcyclists Assoc. Wheels Of Destiny Chapter #735 PA Wilds NE/Eastern Canada regional rally July 2012 Eureka Springs National 2015 Rolling Thunder Washington DC 2016 NE US / E Canada Rally - Mont Tremblant, QC 2016 VRA Eastern National at Maggie Valley 2017 99 Nomad G1 gone but never forgotten traded 4/8/17 for a 2017 Indian Roadmaster
Last edited by minst7877; 09-22-2014 at 09:57 PM.
|
|
|
|
09-22-2014, 10:08 PM
|
#3 |
Join Date: May 2009
Location: Greenwood, Ark.
Posts: 4,736
|
Check out this page. A lot of info and pictures.
__________________
 Dave Jesse 2012 1700 Gray/Black Voyager 2006 1600 Nomad Green/Silver Sold VBA #1108 2010- Eureka Springs - Antlers - 2011- Maggie Valley - Antlers 2012- Margaritaville Ride - Van Buren - Antlers - 2013- Estes Park - Antlers 2014- Mountain View - Antlers - 2015- Eureka Springs - Antlers 2016- Salem - Antlers - 2017- Eureka Springs - Lake George - Antlers - 2018- Custer - Antlers |
|
|
|
09-22-2014, 10:37 PM
|
#4 |
|
Join Date: Oct 2010
Location: Michigan
Posts: 1,286
|
Look at the page posted in the previous post and look at the 3rd picture yellow circle around the spring and back of the switch. That nut has a couple of locking tabs that can be compressed and it then just pulls from the bracket. No twisting and turning and better yet when you snap it back into place on reassembly and reconnect the spring your switch should still be properly adjusted. That is the same setup mine has.
DC
__________________
Me and my 99 G1 Nomad on US 2 by the Lake Michigan Shoreline. Judge's Oil Gear failed and engine overhauled @ 35563 miles VBA/KawaNOW #01625 Christian Motorcyclists Assoc. Wheels Of Destiny Chapter #735 PA Wilds NE/Eastern Canada regional rally July 2012 Eureka Springs National 2015 Rolling Thunder Washington DC 2016 NE US / E Canada Rally - Mont Tremblant, QC 2016 VRA Eastern National at Maggie Valley 2017 99 Nomad G1 gone but never forgotten traded 4/8/17 for a 2017 Indian Roadmaster |
|
|
Linear Mode
