|
02-12-2018, 11:06 PM | #1 |
Member
Join Date: Dec 2017
Location: West Central Washington
Posts: 194
|
FI light & no start
Need some help. Without going into too much detail and humiliating myself.....was working on my '01 Nomad, standing on the right side, when it started "leaning" towards me and falling over. Grabbed under the tank and the seat to try to stop it (handle bars were off), and the tank "got loose". Got the bike back up and on the kickstand. Put it all back together, tank still loose (rocks from side to side), and tried to start. Everything seemed to be okay until I hit the start button. FI light is on and there's no power. Assume something is loose under the tank. Hopefully a connector that I can simply plug back together.
Anyone experienced anything similar? The shop manual I have is not the correct one for the FI model so the procedure for removing the tank, and the connectors under it, aren't covered. HELP. Login or Register to Remove Ads |
|
02-13-2018, 12:40 AM | #2 | |
Member
Join Date: Jun 2014
Location: Inez, KY
Posts: 280
|
Quote:
__________________
"When all is said and done, there's usually more said than done" unknown "Ride hard or stay home" Joe Robinson aka Old Dog, R.I.P |
|
|
02-13-2018, 08:08 AM | #3 |
Top Contributor
Join Date: Feb 2008
Location: Ontario
Posts: 6,925
|
If I am not mistaken I think there is a tip over sensor that shuts the engine off in the event of a spill.
I am not sure if it would be activated if the engine was not running at the time of the spill. It is only activated for so long. Have you tried starting it again this morning ?
Last edited by redjay; 02-13-2018 at 11:55 AM.
|
|
02-13-2018, 07:31 PM | #4 |
Top Contributor
Join Date: Feb 2008
Location: Ontario
Posts: 6,925
|
Did you try the bike this evening ?
|
|
02-14-2018, 01:06 AM | #6 |
Member
Join Date: Dec 2017
Location: West Central Washington
Posts: 194
|
In checking the tank, found the tank was off the front connection. Took the nut off and had to install a flat washer. Tightened the nut and it's better, but still has about 1/2" play from side to side.....not tight. Guess I'll keep working on it 'til I find out why. Not riding it until I do.
|
|
02-14-2018, 07:56 AM | #7 |
Sr. Member
Join Date: May 2015
Location: Saskatchewan , Canada
Posts: 1,441
|
If you look at the underside of the tank you'll see a round rubber gasket ( looks like a 2" cap ) on each side . One of mine fell off while I was working on my bike . Found it laying on the throttle body . I used a bit of silicone to hold them in place . There are also rubber pads on the top of the frame where the tank sits , one on each side .
Part # 92075 , # 92160A Hope this helps www.kawasakipartshouse.com/oemparts/a/kaw/500b268af8700223e4790782/fuel-tank-1-3-vn1500-l2
Last edited by Ridefree; 02-14-2018 at 08:04 AM.
|
|
02-14-2018, 11:03 AM | #8 |
Member
Join Date: Dec 2017
Location: West Central Washington
Posts: 194
|
Dampers
Thanks for comment on the pads. I went on Partzilla to see all the parts of the tank install. There are two pads that sit on the frame and two round dampers....all the parts you mentioned. Waiting for the sun to come out and warm things up in my shed before I go work on it.
Again, thanks! |
|