Chuckster 7 in backing plate/filter

flavor · 02-07-2010, 12:38 PM

Right now have Dobeck TFI, Roadhouse exhaust and 9" spectro single intake filter set up. I think the 7 in diameter set up looks better but looking for some pictures to compare. So you guys that went to the 7" intake post some pictures if you would.

Hey MAC what's involved if I change to the 7"?

cactusjack · 02-07-2010, 02:17 PM

Quote:

Originally Posted by flavor

Right now have Dobeck TFI, Roadhouse exhaust and 9" spectro single intake filter set up. I think the 7 in diameter set up looks better but looking for some pictures to compare. So you guys that went to the 7" intake post some pictures if you would.

Hey MAC what's involved if I change to the 7"?

Here's mine:

This is the front side of the 7" backing plate:

and here's the back side:

Here it is installed with the K&N filter:

another:

I just realized these pictures are a little out of sequence. The white breather filter you see beneath the air cleaner housing was how I first had it set up. It wasn't until later that I added the 90° brass elbow and attached the breather tube to the plate.

dkdixie · 02-07-2010, 04:15 PM

Favor, Here's mine using two Chuckster 7" plates and stock dog bowls.

reaper · 02-07-2010, 06:46 PM

I just installed the 7"plate today.
It's fairly simple.
Just a matter of removing a few screws, swapping a couple of items over and bing your done.
30 minutes max.
Pics to follow

dabull · 02-07-2010, 07:21 PM

Quote:

Originally Posted by "Reaper" - Doug Grimm

I just installed the 7"plate today.
It's fairly simple.
Just a matter of removing a few screws, swapping a couple of items over and bing your done.
30 minutes max.
Pics to follow

sweet...looking forward to it as i am seriously thinking of doing this too...

**Jared** · 02-07-2010, 08:40 PM

+1

Easy mod and makes a noticeable difference.

flavor · 02-08-2010, 09:26 AM

Thanks for the pictures. Appreciate all the effort you and others make to give info. Definitely considering the 7 in plate and K&N filter set up.

Quote:

Originally Posted by cactusjack

Quote:

Originally Posted by flavor

Right now have Dobeck TFI, Roadhouse exhaust and 9" spectro single intake filter set up. I think the 7 in diameter set up looks better but looking for some pictures to compare. So you guys that went to the 7" intake post some pictures if you would.

Hey MAC what's involved if I change to the 7"?

Here's mine:

This is the front side of the 7" backing plate:

and here's the back side:

Here it is installed with the K&N filter:

another:

I just realized these pictures are a little out of sequence. The white breather filter you see beneath the air cleaner housing was how I first had it set up. It wasn't until later that I added the 90° brass elbow and attached the breather tube to the plate.

rez · 02-08-2010, 09:09 PM

My 2005 Nomad, which I just purchased, has a 9408 Kuryakyn Hypercharger. I am disappointed/concerned in the interference with right leg and knee and difficulty to get on to the brake pedal. I am seriously thinking of doing Chuckster's mod with stock dog bowl. Would anyone have a stock dog bowl for sale?

**Jared** · 02-08-2010, 09:17 PM

Rez, PM sent.

macmac · 02-09-2010, 07:55 PM

Cj, what did you do with the 2 metal lines that used to be the uh er um ISC's yeah the ISC's...

I assume capped them off back more somewhere???

Jim, either a cover like Cj's or a stock dog bowl like dk dixie. Or anything else you come by.

A fitting like Cj's brass one, and a new bolt like Cj's, all of which I can get on demand local, if you want me.

For Pete this would be easy as well. Just bring him these pics.

Do Not ride to NH now... My driveway is a sheet of ice, I have snow and more in the forecast!

cactusjack · 02-09-2010, 11:11 PM

Quote:

Originally Posted by macmac

Cj, what did you do with the 2 metal lines that used to be the uh er um ISC's yeah the ISC's...

I assume capped them off back more somewhere???

Jim, either a cover like Cj's or a stock dog bowl like dk dixie. Or anything else you come by.

A fitting like Cj's brass one, and a new bolt like Cj's, all of which I can get on demand local, if you want me.

For Pete this would be easy as well. Just bring him these pics.

Do Not ride to NH now... My driveway is a sheet of ice, I have snow and more in the forecast!

I removed them all the way back to the throttle body and capped the fittings on the throttle body where the rubber hoses were connected.

flavor · 02-10-2010, 09:27 AM

Thanks for the info. Sorry but not going north to your house anyway,

Don't want to go to colder weather...........now if north was warmer.........

Quote:

Originally Posted by macmac

Cj, what did you do with the 2 metal lines that used to be the uh er um ISC's yeah the ISC's...

I assume capped them off back more somewhere???

Jim, either a cover like Cj's or a stock dog bowl like dk dixie. Or anything else you come by.

A fitting like Cj's brass one, and a new bolt like Cj's, all of which I can get on demand local, if you want me.

For Pete this would be easy as well. Just bring him these pics.

Do Not ride to NH now... My driveway is a sheet of ice, I have snow and more in the forecast!

flavor · 02-10-2010, 09:30 AM

Hey CJ thanks for the pictures. I like that set up with the K&N. I'm leaning that direction.

Quote:

Originally Posted by cactusjack

Quote:

Originally Posted by flavor

Right now have Dobeck TFI, Roadhouse exhaust and 9" spectro single intake filter set up. I think the 7 in diameter set up looks better but looking for some pictures to compare. So you guys that went to the 7" intake post some pictures if you would.

Hey MAC what's involved if I change to the 7"?

Here's mine:

This is the front side of the 7" backing plate:

and here's the back side:

Here it is installed with the K&N filter:

another:

I just realized these pictures are a little out of sequence. The white breather filter you see beneath the air cleaner housing was how I first had it set up. It wasn't until later that I added the 90° brass elbow and attached the breather tube to the plate.

macmac · 02-10-2010, 11:43 AM

Quote:

Originally Posted by cactusjack

Quote:

Originally Posted by macmac

Cj, what did you do with the 2 metal lines that used to be the uh er um ISC's yeah the ISC's...

I assume capped them off back more somewhere???

Jim, either a cover like Cj's or a stock dog bowl like dk dixie. Or anything else you come by.

A fitting like Cj's brass one, and a new bolt like Cj's, all of which I can get on demand local, if you want me.

For Pete this would be easy as well. Just bring him these pics.

Do Not ride to NH now... My driveway is a sheet of ice, I have snow and more in the forecast!

I removed them all the way back to the throttle body and capped the fittings on the throttle body where the rubber hoses were connected.

Thanks Cj. I figured that was how, but wanted to be sure. I am aware the steel turns back to tubing again.

So far when I have done these it has been with the idea to go back to stock on a whim. I don't trust state regs and epa much.

Flavor, Well, IOU, and Pete don't

blowndodge · 02-10-2010, 12:05 PM

That's what I'm think of to Mac. Being able to undo this in a moments notice when the CARB comes a knocking..... One thing I don't like is the drastic (to me anyway) increase in intake noise.

CJ with your setup now with the Cobras TD's I'm assuming your "dialed in" on the fuel processor? If so do you think your mods have a noticable increase in power or just more noise or both? From just a power stand point are pipes and open air cleaner worth it? Pipes $500 bucks, About $70 for chucksters plate and K&N.

$570 for only more noise wouldn't reach my threshold of worthwhile mods.... JMHO

02-07-2010, 12:38 PM	#1
flavor Sr. Member Join Date: Apr 2008 Location: RI Posts: 1,351	Chuckster 7 in backing plate/filter Right now have Dobeck TFI, Roadhouse exhaust and 9" spectro single intake filter set up. I think the 7 in diameter set up looks better but looking for some pictures to compare. So you guys that went to the 7" intake post some pictures if you would. Hey MAC what's involved if I change to the 7"? Login or Register to Remove Ads
	0

02-07-2010, 04:15 PM	#3
dkdixie Sr. Member Join Date: Nov 2007 Location: Blairsville in N. GA mountains Posts: 1,623	Chuckster 7 in backing plate/filter Favor, Here's mine using two Chuckster 7" plates and stock dog bowls. __________________ Dick Campbell Blairsville, GA 2008 Red & Black Nomad 1600 (retired) 2009 1900 Yamaha Stratoliner (retired) 2013 1900 Yamaha Stratoliner 2018 CanAm RT Limited Spyder (Sold) 2014 Goldwing Roadsmith Red Trike (Sold) 2019 Goldwing DCT Roadsmith Copper & Black Trike VBA #243 Darkside #115 Patriot Guard Rider American Legion Rider
	0

02-07-2010, 06:46 PM	#4
reaper Advanced Member Join Date: Nov 2008 Location: St. Augustine, FL Posts: 591	Chuckster 7 in backing plate/filter I just installed the 7"plate today. It's fairly simple. Just a matter of removing a few screws, swapping a couple of items over and bing your done. 30 minutes max. Pics to follow __________________ Doug 08 1600 Nomad FI Metallic Ocean Blue / Neutron Silver Web Slinger's Speedo face, Chuckster's Air Kit, Jay's LED Tail light, dshelly's throttle mod, Kuryakan Deep Bezel lens, Headlight Modulator, Kuryakan Run/Brake/Turn, DWG 2" speakers and amp, Stebel Air Horn Fire & Iron, Red Knights, ROK, VBA, VRA, VROC, IAFF
	0

02-07-2010, 08:40 PM	#6
Jared Join Date: Mar 2009 Location: Greeley, Colorado Posts: 6,772	Chuckster 7 in backing plate/filter +1 Easy mod and makes a noticeable difference. __________________ Jared VBA #1051 (Former President)
	0

02-08-2010, 09:09 PM	#8
rez Member Join Date: Jan 2010 Location: Stoney Creek,ON Canada Posts: 77	Chuckster 7 in backing plate/filter My 2005 Nomad, which I just purchased, has a 9408 Kuryakyn Hypercharger. I am disappointed/concerned in the interference with right leg and knee and difficulty to get on to the brake pedal. I am seriously thinking of doing Chuckster's mod with stock dog bowl. Would anyone have a stock dog bowl for sale?
	0

02-08-2010, 09:17 PM	#9
Jared Join Date: Mar 2009 Location: Greeley, Colorado Posts: 6,772	Chuckster 7 in backing plate/filter Rez, PM sent. __________________ Jared VBA #1051 (Former President)
	0

02-09-2010, 07:55 PM	#10
macmac Sr. Contributor Join Date: Apr 2008 Location: Tamworth New Hampster 06 1600 Posts: 12,484	Chuckster 7 in backing plate/filter Cj, what did you do with the 2 metal lines that used to be the uh er um ISC's yeah the ISC's... I assume capped them off back more somewhere??? Jim, either a cover like Cj's or a stock dog bowl like dk dixie. Or anything else you come by. A fitting like Cj's brass one, and a new bolt like Cj's, all of which I can get on demand local, if you want me. For Pete this would be easy as well. Just bring him these pics. Do Not ride to NH now... My driveway is a sheet of ice, I have snow and more in the forecast! __________________ 06 1600 Nomad Just call me Mac molon labe come and get it
	0

02-10-2010, 12:05 PM	#15
blowndodge Sr. Contributor Join Date: Jul 2007 Location: Washington City, Utah Posts: 16,474	Chuckster 7 in backing plate/filter That's what I'm think of to Mac. Being able to undo this in a moments notice when the CARB comes a knocking..... One thing I don't like is the drastic (to me anyway) increase in intake noise. CJ with your setup now with the Cobras TD's I'm assuming your "dialed in" on the fuel processor? If so do you think your mods have a noticable increase in power or just more noise or both? From just a power stand point are pipes and open air cleaner worth it? Pipes $500 bucks, About $70 for chucksters plate and K&N. $570 for only more noise wouldn't reach my threshold of worthwhile mods.... JMHO __________________ I love my Victory Cross Country Tour 106. Smells like Victory! Ultra's are Limited There are two types of Harley riders. Those that trailer them and those that push them. The most Interesting Man in the World "Find the things in life you don't do well and don't do those things" Member # 0005
	0

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Chuckster back plate with 7" K&N	Jared	Vulcan Nomad/Vaquero/Voyager	15	07-06-2012 05:46 AM
7" backing plate filter	shoer00	1500 & 1600 Nomad	8	03-20-2010 08:44 PM
"Chuckster" plate w/stock cover or open filter	dkdixie	1500 & 1600 Nomad	13	04-18-2009 08:18 AM
"NEW" Chuckster backing plate (Update Pg 6)	dkdixie	1500 & 1600 Nomad	117	04-06-2009 08:14 PM
License Backing Plate	dogdoc	Parts & Accessories	17	09-26-2008 01:53 PM