|
![]() |
#17 |
Member
Join Date: Jul 2015
Location: AJ, Arizona
Posts: 57
|
So its just the normal backlash of a bike with 61K? Went and talked to a mechanic today and he said if it was his bike he would leave it, they make noise, its normal as I have seen many others say over the years. I reckon I will put it back together & keep riding.
|
![]() |
![]() |
#18 | |
Sr. Member
Join Date: Nov 2013
Location: The Newforest, England
Posts: 4,664
|
Quote:
![]()
__________________
|
|
![]() |
![]() |
#19 |
Top Contributor
Join Date: Feb 2008
Location: Ontario
Posts: 6,945
|
Was the universal joint replaced ? Was the original worn ?
|
![]() |
![]() |
#20 |
Member
Join Date: Jul 2015
Location: AJ, Arizona
Posts: 57
|
The noise I hear is new and only when accelerating at higher speeds, just noticed something different recently. Had the bike for like 6 or 7 years and occasionally cruise at around 90mph and it usually sounds so nice :) If I was wearing a helmet though I may not even hear it. Always appreciate your comments Mick, thanks!
Login or Register to Remove Ads |
![]() |
![]() |
#21 |
Member
Join Date: Jul 2015
Location: AJ, Arizona
Posts: 57
|
Orignal looks good and I showed it to a
"retired" mechanic today and he said its good. Have a new one though, perhaps I should replace while I have the drive shaft out? The orig does seem just fine.
Last edited by virtualgeorge; 01-13-2023 at 09:30 PM.
|
![]() |
![]() |
#22 |
Top Contributor
Join Date: Feb 2008
Location: Ontario
Posts: 6,945
|
If you have the part and the driveshaft is apart I would replace the universal joint.
|
![]() |
![]() |
#23 |
Member
Join Date: Jul 2015
Location: AJ, Arizona
Posts: 57
|
|
![]() |
![]() |
#24 | |
Sr. Member
Join Date: Nov 2013
Location: The Newforest, England
Posts: 4,664
|
Quote:
![]()
__________________
|
|
![]() |
![]() |
#25 |
Member
Join Date: Jul 2015
Location: AJ, Arizona
Posts: 57
|
When I made the video I was twisting the gear back and forth but actually I would hear that same sound when rolling the bike or spinning the tire when on the lift.
I saw this old thread which sounded like the exact same issue so suspected the bevel gear bearing? http://vulcanbagger.com/forums/showt...l+gear+bearing All the old pics are gone though. But before I put it back together, is there any way to rule out the bevel gear bearing? His symptoms did seem very similar and I do have the bearing in the freezer. |
![]() |
![]() |
#26 |
![]() Join Date: Jan 2009
Location: Psychiatric Ward FL
Posts: 3,429
|
Call me @ 5612103399, it's one of the bevel gear bearings.
I've done a few of these in my time.
__________________
MT 2016 FLHP Psychiatric Ward FL VBA 936 |
![]() |
![]() |
#27 |
![]() Join Date: Oct 2013
Location: chandler okla
Posts: 854
|
take Mas up on His Offer
|
![]() |
![]() |
#28 |
Member
Join Date: Jul 2015
Location: AJ, Arizona
Posts: 57
|
Yes I'm going to talk to him today, I wouldn't pass up on that offer
|
![]() |
![]() |
#29 |
Member
Join Date: Jul 2015
Location: AJ, Arizona
Posts: 57
|
I ask a lot of bonehead questions & not very mechanically inclined but thanks to MAS I got the bevel gear bearing replaced. MAS is a good human, he gave a few tips on things I would have never figured out on my own. I appreciate everyone else's help as well over the years :)
Didn't see many flakes on the screen & when I removed the housing I ran a magnet around the inside and it did pick up some very fine bearing flakes. So I guess I will do a few oil changes with some cheap oil to hopefully flush them out? |
![]() |